Need help with norns-shield?
Click the “chat” button below for chat support from the developer who created it, or find similar developers for support.

About the developer

monome
236 Stars 27 Forks GNU General Public License v3.0 38 Commits 0 Opened issues

Description

minimal/tiny open-source/DIY shield for Raspberry Pi boards, providing hardware compatibility with the norns ecosystem.

Services available

!
?

Need anything else?

Contributors list

norns-shield

minimal/tiny open-source/DIY shield for Raspberry Pi boards, providing hardware compatibility with the norns ecosystem.

  • audio codec: CS4270
  • audio jacks: 3.5mm stereo in/out, line level
  • OLED: NHD-2.7-12864WDW3
  • 3x pushbuttons, 3x rotary encoders

see the full BOM on Octopart

see https://llllllll.co/t/diy-norns-shield for discussion.

monome.org

full kit available from monome.org

assembly

for SMD-populated circuit.

parts shown (header already soldered to OLED)

first solder the OLED header (make sure the orientation looks like the photo below, as we've had a few reports of folks placing their headers on the wrong side). then the encoders, and keys.

then attach the pi header to the other side and solder as shown.

attach the screen to the top. note that you may have to apply substantial pressure for it to connect: put something hard on top of the header while applying pressure so you don't wreck your thumbs.

likewise, attaching the keycaps requires substantial pressure. be sure they are aligned well then press hard.

the knobs should go on easily in comparison.


attach the shortest spacers with short screws, which props up the screen.

four spacers with the male thread insert from the top. for the bottom, the long remaining spacers go in front, shorter in back as shown.

align the plate and attach with short screws. don't tighten the screws until you've aligned the keys and knobs, as there's a little wiggle room for fine tuning.

attach the pi and add two plastic spacers, then balance the plate on top. the holes with spacers need the two long screws, the front use short screws.

setting up

get this shield image from github. nb. image is only compatible with Raspberry Pi 3b+ and Pi 3b. Pi 4 is not supported out of the box. for more detail, see this thread.

use etcher to make your SD card. it's by far the most reliable method.

troubleshooting

  • most soldering problems can be solved simply by reheating solder joints. bad solders can result in various problems: screen doesn't turn on, knobs/keys don't work.
  • use a good SD card, not a cheap one. if you're having trouble, try using a different card.
  • be sure to use the correct power supply. the pi will not power well from a laptop and you'll get confusing errors. get a dedicated 2A USB supply, or very high output USB battery.

if your SD card seems a lot more full than it should be, you'll need to expand the filesystem: - open a terminal on a computer connected to the same network as your shield - execute:

ssh [email protected]
- password:
sleep
- execute:
sudo raspi-config
- navigate to
Advanced
and hit RETURN - select
expand filesystem
and hit RETURN - lots of activity will happen. when it's done, power down and reboot. if you get any errors, reboot again. - if you SSH back into norns and execute
df -h
, you'll see the newly expanded capacity.

notes

  • the shield does not have a headphone output, but headphones work fine on the main output. the headphone gain level within the norns menu does nothing in this case.
  • the battery indication will not function, as there's no battery.

mechanicals

  • 2 Female Threaded Hex Standoff Aluminum, 3/16" Hex, 5/16" Long, 2-56 Thread 91780A104
  • 2 Female Threaded Hex Standoff Aluminum, 3/16" Hex, 5/8" Long, 2-56 Thread 91780A111
  • 2 Female Threaded Hex Standoff Aluminum, 3/16" Hex, 3/4" Long, 2-56 Thread 91780A113
  • 4 Male-Female Threaded Hex Standoff Aluminum, 3/16" Hex Size, 1/2" Long, 2-56 Thread Size 93505A213
  • 4 Off-White Nylon Unthreaded Spacer 1/4" OD, 3/32" Long, for Number 6 Screw Size 94639A247
  • 8 Black-Oxide 18-8 Stainless Steel Pan Head Phillips Screws 2-56 Thread, 1/4" Long 91249A050
  • 2 Black-Oxide 18-8 Stainless Steel Pan Head Phillips Screws 2-56 Thread, 3/8" Long 91249A054

We use cookies. If you continue to browse the site, you agree to the use of cookies. For more information on our use of cookies please see our Privacy Policy.